ข้อมูลพื้นฐาน
Automatic Grade
Automatic
Type
Metallurgy Machinery
แพคเพจการขนส่ง
Nude Packing
รหัสพิกัดศุลกากร
8474390000
คำอธิบายสินค้า
Three stage dry lime hydratorThe main body of the machine is constituted by three superimposed chambers, called "stages".
1st stage
In the first stage, the quicklime receives the hydration water, which is previously water line arranged from water station.
The mixture of prepared water and abated dust is collected in the bottom of the filter to hydrator, and water is transferred to the feeding mouth of the machine.
The prepared water is involved the hydration reaction, throughout 1st stage, thanks to the strong mixing of the shaft provided with steel paddles.
2nd stage
The lime at the end of the first stage falls into the 2nd stage where the hydration reaction is completed. During the transformation of oxide into hydrate, the apparent specific weight of material is reduced to an half. For this reason, the 2nd stage volume is twice as much as that of the 1st stage. Two paddle agitators mix the material, favoring the completion of reaction, and transport it up to the following stage.
3rd stage
The reaction is completed for most of the material, which is then homogenized in the third stage.
This chamber is provided with two paddle agitators to mix and there is an adjustable weir that allows the material level in this stage to be adjusted according to the characteristics of the used quicklime. The overburnt material, with a slower reaction speed and a higher specific weight, will have a tendency to fall down in the bottom of the chamber and its retention time will be higher allowing a higher degree of completion of the hydration process before the material leaves the hydrator.1. Application areas and key functionsMulti-stage dry power(burnt lime power) hydrator is widely used in environmental desulfurization, semi-dry desulfurization, lime finishing, fine chemical and other industries. Using our three-stage dry powder hydrator, burnt lime will be hydrated into a fluffy powder because the hierarchical & reasonable water distribution and multi-channel process of this hydrator. 2. Principles and performanceOur advantages and principles of three-stage dry power hydrator as below:
It will control the reaction time and fully hydrate the CaO by only 15-20 minutes.
Hydrator has good heat-insulating property. The unique design makes a lot of heat generated in the reaction of CaO to be converted inside and reused. It will raise the inner temperature to 60 degrees by only 3-5 minutes and make the CaO to be fully hydrated.
Feeding process control: Sending the needed materials into the first-stage reaction cabin through the screw feeder.
Advantages: There are lots of hot steam and dust when CaO contact with water. This feeding way will provent them flowing back the screw feeding counter, so that will not affect the accuracy of sensor.Three-stage hydrate reaction with water distribution
The hierarchical & scientific distribution of water can make the CaO to be fully pre-hydrated. Afer contacting with reasonable water in the first stage reaction cabin, then enter into the second one. This process is the best reaction time of CaO. When entering into the third one, hydrated CaO is semi-dry state. The whole three stages finally make the CaO completely become the fluffy powder. And the entire reaction process needs about 15-20 minutes.3. Equipment superioritiesThis device, according to environmental requirements, could collocate with dust removal device which will solve the problem of the steam & dust pollution produced during hydration of quicklime. At the same time this device also can be matched with the follow-up process equipments, such as lime pulping machine, slurry-residue separation machine, filters etc. So it can produce the high purity lime emulsion to meet the needs of concentration.4. Parameter requirementsBecause our Three-stage dry power hydrator is non-standard equipment and should be customized according your denamd. So please help to provide the following parameters:
Application and process status for multi-stage dry power hydrator
Lime particle size, purity and degree of activity
Lime feeding amount per hour
If need to match dust removal device
Water control of the lime and other requirements
ที่อยู่:
Nanjing, Jiangsu, China
ประเภทของธุรกิจ:
ผู้ผลิต/โรงงานผลิต
ขอบเขตธุรกิจ:
บริการ, อุปกรณ์และส่วนประกอบอุตสาหกรรม, เครื่องจักรการผลิตและแปรรูป
แนะนำบริษัท:
บริษัท Nanjing Lime Machinery Co., Ltd. เป็นบริษัทขนาดใหญ่ที่เชี่ยวชาญในการผลิตอุปกรณ์เติมน้ำที่ใช้ในการผลิตผงแป้ง บริษัทของเรามีความเป็นมืออาชีพในการออกแบบและผลิตอุปกรณ์ที่หลากหลายสำหรับโรงงานและพื้นที่ต่างๆ : ระบบการผลิตน้ำมะนาวเพื่อเป็นมิตรกับสิ่งแวดล้อมซึ่งใช้สำหรับอุตสาหกรรมเคมีปูน , แคลเซียมไฮดรอกไซด์ผลิตสายการผลิตสำหรับคนผิวแห้งเบา , ผลิตแมกนีเซียมไฮดรอกไซด์ , อุปกรณ์การผลิตสำหรับการผลิตวัสดุก่อสร้างสำหรับพื้นที่การทำเหมือง อุปกรณ์การทำให้แห้งตัวลง , เครื่องบำบัดด้วยแคลเซียมในการบำบัดน้ำเสีย , ท่อผลิตปูนขาวน้ำคุณภาพสูง , เครื่องกรองฝุ่นหินปูนเปียก เรามีสิทธิ์ในการนำเข้าส่งออกและตัวแทนรวมทั้งการวิจัยออกแบบผลิตและจำหน่ายอุปกรณ์เสริมและผลิตภัณฑ์ของเราก็ได้สร้างประชากรที่ดีกว่าทุกคำพูด
เราแก้ปัญหาเรื่องความชุ่มชื้นแบบมะนาวให้กับลูกค้าด้วยเครื่องที่มีคุณภาพดีที่สุดและบริการที่เปี่ยมด้วยความเอาใจใส่ เพื่อให้สอดคล้องกับแนวคิดการปกป้องสิ่งแวดล้อมและการประหยัดพลังงานเรามุ่งเน้นที่นวัตกรรมทางเทคนิคการซึมซับเทคโนโลยีและทักษะการจัดการขั้นสูงทั้งภายในและภายนอกอย่างต่อเนื่องแล้วผนวกความต้องการที่แท้จริงของลูกค้าปรับปรุงผ่านการปฏิบัติเพื่อพัฒนาผลิตภัณฑ์ที่ดียิ่งขึ้น โดยเฉพาะอย่างยิ่งเมื่อมีเป้าหมายที่ปัญหาฝุ่นที่เกิดจากน้ำที่สูญเสียเราสามารถให้การออกแบบกระบวนการเพิ่มความชุ่มชื้นการปรับปรุงทางเทคนิคการฝึกอบรมบุคลากร