ข้อมูลพื้นฐาน
คำอธิบายสินค้า
MR092E Electrotechnics Theory, Electric Traction Trainer lab equipment electrical laboratory equipment for university1 Product overview1-1 Overview1. The electric teaching aid adopts advanced design, and the experimental panel can be replaced freely. Students can replace it according to different training requirements.2. The experimental instruments are digital display with high precision. The power and instruments used in this trainer are equipped with a reliable personal safety protection system.1-2 Features3. Applicable to the teaching of "Basic Theory of Electrical Engineering" and "Electrical Technology". Thanks to its good expansion capabilities, the trainer can be extended to other training content such as "Programmable Logic Controller Technology" and "Motor Variable Frequency Control".4. The front panel of the hanging test board is drawn with schematic diagrams and symbols, and the other side is welded with related parts. Components that need to be measured or observed use a locking connector. The experimental circuit adopts the unit circuit mode design. Each unit circuit is based on the basic circuit. By connecting different components or combining different circuits, students can practice various training contents on the trainer.2 Performance parameters(1) Input power: three-phase five-wire system 380V±10% 60Hz(2) Dimensions: 1600mm × 800mm × 1500mm(3) Machine capacity: <2KVA(4) Weight: <250kg(5) Working conditions: ambient temperature -10 ° C ~ +40 ° C Relative humidity <85% (25 ° C)4 Experiment list Electrician basic electric drag partExperiment 1 The use of basic electrical instruments and the calculation of measurement errorsExperiment 2 Method for reducing the measurement error of the meterExperiment 3 Ohm's lawExperiment 4 Instrument Range ExtensionExperiment 5 Mapping of volt-ampere characteristics of linear and nonlinear circuit componentsExperiment 6 Determination of potential and voltage and drawing of circuit potential mapExperiment 7 Verification of Kirchhoff's Law
Experiment 8 Verification of the superposition principleExperiment 9 Equivalent transformation of voltage source and current sourceExperiment 10 Verification of Thevenin's TheoremTest 11 Verification of Norton's Theorem--Determination of Equivalent Parameters of Active Two-End NetworkExperiment 12 Determination of maximum power transmission conditionsExperiment 13 Two-port network testExperiment 14 Reciprocity TheoremExperiment 15 Experimental study of controlled sources VCVS, VCCS, CCVS, CCCSExperiment 16 Observation and measurement of typical electrical signalsExperiment 17 Response test of RC first-order circuitExperiment 18: Study on the response of second-order dynamic circuitExperiment 19: Determination of impedance characteristics of R, L and C componentsExperiment 20 RC string, parallel double T frequency selection network characteristics testExperiment 21: Research on R, L, C Series Resonant CircuitsExperiment 22 RC dual T frequency selective networkExperiment Twenty-three Study of Phasor Trajectories in RL and RC Series CircuitsExperiment 24: R, L, C component characteristics and AC parameters determinationExperiment 25 Measurement of AC circuit parametersExperiment 26 Study on phasor of sinusoidal steady-state AC circuitExperiment 27 Test of characteristics of single-phase iron core transformerExperiment 28: Determination of winding polarity of transformerExperiment 29 Verification of single-phase watt-hour meterExperiment 30 Measurement of power factor and phase sequenceExperiment 31: Negative Impedance ConverterExperiment thirty-two gyrator
Experiment 33: Fluorescent lamp, white woven lamp, watt-hour meter installation control circuitExperiment 34: Use of three-phase squirrel cage asynchronous motorExperiment 35: Three-phase asynchronous motor jogExperiment 36: Three-phase asynchronous motor self-locking control circuitExperiment 37: Three-phase asynchronous motor can both jog and self-lock control linesExperiment 38: Contactor interlocking positive and negative control lineExperiment 39: Button interlocking positive and negative control lineExperiment 40 button and contactor double interlocking positive and negative control lineAnalog circuit sectionExperiment 1 Use of commonly used electronic instrumentsExperiment 2 Transistor common emitter single tube amplifierExperiment 3 FET amplifierExperiment 4 Negative Feedback AmplifierExperiment 5 emitter followerExperiment 6 Difference AmplifierExperiment 7 Integrated Operational Amplifier Indicator Test 146Lab 8 Basic Applications of Integrated Operational Amplifiers (I)--- Analog Operational CircuitsLab 9 Basic Application Gates for Integrated Operational Amplifiers (II) --- Active FiltersLab 10 Basic Applications of Integrated Operational Amplifiers (III)--- Voltage ComparatorsLab 11 Basic Applications of Integrated Operational Amplifiers (IV) --- Waveform GeneratorsExperiment 12 RC sine wave oscillatorExperiment 13 LC sine wave oscillatorExperiment 14 Assembly and debugging of function signal generatorExperiment 15 Voltage Controlled Oscillator
Experiment 16 Low Frequency Power Amplifier (I) --- OTL Power AmplifierExperiment 17 Low Frequency Power Amplifier (I) --- Integrated Power AmplifierExperiment 18 DC regulated power supply (I) --- series transistor regulated power supplyExperiment 19 DC regulated power supply (II) --- integrated voltage regulatorExperiment 20 Thyristor controllable rectifier circuitExperiment 21 Application Experiment --- Temperature Monitoring and Control CircuitExperiment Twenty-two Comprehensive experiment Design and debug of a multimeter using operational amplifiersAppendix I Principles and Use of OscilloscopesAppendix II Detection of common electronic components with a universal meterAppendix III Resistor Nominal Value and Accuracy Color Circle Marking MethodAppendix IV Amplifier Interference, Noise Suppression, and Elimination of Self-Excited OscillationDigital circuit partExperiment 1 Transistor Switching Characteristics, Limiter and ClampExperiment 2 Logic function and parameter test of TTL integrated logic gateExperiment 3 Logic function and parameter test of CMOS integrated logic gateExperiment 4 Connection and drive of integrated logic circuitsExperiment 5 Design and test of combinatorial logic circuitExperiment 6 Decoder and its applicationExperiment 7 Data Selector and Its Application
Experiment 8 Trigger and its applicationExperiment 9 Counter and its applicationExperiment 10 Shift register and its applicationExperiment 11 Pulse Distributor and Its ApplicationExperiment 12 Using a Gate Circuit to Generate a Pulse Signal--Self-excited MultivibratorExperiment 13 Monostable Trigger and Schmitt Trigger---Pulse Delay and Waveform Shaping CircuitExperiment 14 555 time base circuit and its applicationExperiment fifteen electronic stopwatchExperiment 16 Electronic code lockExperiment 17 Digital Frequency MeterExperiment 18Experiment 19 D/A, A/D converterServiceWe supply supply7*24 hours service, customer design service, OEM service, buyer label service. With professional engineers team and sales team, we assure you good product quality.CertificateOur products takes ISO9001 product management system.No. | Feature Name | Details |
1 | Customer design | Yes |
2 | Warranty | 1 year, 2 years, 3 years or 5 years according to client requirements |
3 | Package | Plastic film+ carton+ Fine plywood |
4 | Products standard | International didactic equipment standard |
5 | Application range | Educational equipment for university, college, vocational training centers |
6 | Company philosophy | Supply best quality Chinese products to the worldwide schools. |
7 | Self owned brand | Minrry,MR |
8 | Production time | From 10 days to 60 days according to different items |
We also have below equipment, please click the link to see itelectrical training equipmentmechatronics training equipment
ที่อยู่:
Building No. 3 Double Innovation and Creation Industry Center, No. 803 Keyuan Road, High Tech Zone, Jinan, Shandong, China
ประเภทของธุรกิจ:
ผู้ผลิต/โรงงานผลิต
ขอบเขตธุรกิจ:
เครื่องใช้สำนักงาน
การรับรองของระบบการจัดการ:
ISO 9001
แนะนำบริษัท:
Jinan Minrry Technology Equipment Co., Ltd. ก่อตั้งขึ้นในปี 2009 เป็นโรงงานผลิตอุปกรณ์การศึกษาอุปกรณ์ฝึกอาชีพอุปกรณ์สอน บริษัท Minrry คือบริษัทไฮเทคและนวัตกรรมมณฑลซานตงโดยมีทีมวิศวกรวิจัยและพัฒนาตนเองและโรงงานผลิตขนาด 5000 ตารางเมตรเป็นเจ้าของเอง
ISO 9001, IS14001, ใบอนุญาต OSHAS18001
การส่งออกผลิตภัณฑ์มีน้อยมากถึง 100 ประเทศ
กลุ่มผลิตภัณฑ์ของเรามีความแตกต่างกันออกไปเช่น
อุปกรณ์ฝึกอบรมระบบไฟฟ้า
การฝึกอบรมระบบเมคคาทรอนิกส์อุปกรณ์การฝึกอบรม
เกี่ยวกับของเหลวอุปกรณ์การ
ฝึกอบรมการระบายความร้อน
การฝึกอบรมความเย็นอุปกรณ์การฝึกอบรม
อุปกรณ์ห้องปฏิบัติการ PCB บริษัท
ของเรานำเสนอผลิตภัณฑ์ที่หลากหลายซึ่งสามารถตอบสนองความต้องการที่หลากหลายของคุณได้ เรายึดมั่นในหลักการบริหาร " คุณภาพต้องมาก่อนลูกค้าต้องมาก่อนและมีการให้เครดิต " นับตั้งแต่ก่อตั้งบริษัทและพยายามอย่างดีที่สุดเสมอเพื่อตอบสนองความต้องการที่อาจเกิดขึ้นของลูกค้าของเรา บริษัทของเรายินดีที่จะร่วมมือกับบริษัทต่างๆทั่วโลกอย่างจริงใจเพื่อสร้างสถานการณ์ที่เป็นหนึ่งในสองฝ่ายของเราเนื่องจากแนวโน้มของโลกาภิวัตน์ทางเศรษฐกิจได้พัฒนาขึ้นโดยมีอำนาจที่ไม่อาจต้านทานได้