| Type: | Seamless Steel Tube / Pipe |
|---|---|
| Standard: | AISI, ASTM, DIN, JIS, GB, BS |
| Composition: | Alloys and Non-Ferrous Metals |
| Technique: | Hot Rolled |
| Shape: | Round |
| Surface Treatment: | Black |
ซัพพลายเออร์ที่มีใบอนุญาตการทำธุรกิจ
ซัพพลายเออร์ที่ผ่านการตรวจสอบแล้ว 
| ASTM 1320 GB 20Mn2 | It has medium strength, small section size, low temperature impact toughness and good weldability. Cold deformation has high plasticity, good machinability, higher hardenability than corresponding carbon steel, and tends to overheat, decarburization sensitivity and temper brittleness during heat treatment. |
| ASTM 1330 GB 30Mn2 | 1330 is usually used after quenching and tempering treatment. It has high strength, good toughness, and excellent wear resistance. When manufacturing parts with small section size, it has good static strength and fatigue strength, good wire drawing, cold heading, and heat treatment process, medium cutting ability, and acceptable weldability. Generally, it is not required to make weldments. When welding is required, the parts should be preheated to more than 200 ° C, with high hardenability and small quenching deformation, However, it has overheating, decarburization sensitivity and temper brittleness. |
| ASTM 1335 GB 35Mn2 | The carbon content is higher than 1330, so it has higher strength and better wear resistance, and the hardenability is also improved, but the plasticity is slightly decreased. During cold deformation, the plasticity is medium, the machinability is medium, the weldability is low, and there is white spot sensitivity, overheating tendency and temper brittleness tendency. Water cooling is easy to produce cracks, and it is generally used in quenched and tempered or normalized conditions. |
| ASTM 1340 GB 40Mn2 | Medium carbon quenched and tempered manganese steel is superior to 1040 steel in strength, plasticity and wear resistance. It has good heat treatment process and machinability, and poor weldability. When the carbon content is below *, it needs to be preheated to 100-425 ºC before welding. It has temper brittleness, overheating sensitivity, and water cooling is easy to produce cracks. It is usually used in quenched and tempered state. |
| ASTM 1345 GB 45Mn2 | Medium carbon quenched and tempered steel has high strength, wear resistance and hardenability. After quenched and tempered, it can obtain good comprehensive mechanical properties. It is suitable for oil cooling and high temperature tempering. It is often used in the quenched and tempered state, and can also be used in the normalized state if necessary. Its machinability is acceptable, but its weldability is poor, its plasticity is low during cold deformation, its heat treatment has a tendency of over-heat sensitivity and temper brittleness, and water cooling is easy to produce cracks. |
| GB 50Mn2 DIN 50Mn2 | Medium carbon quenched and tempered high strength manganese steel has high strength, high elasticity and excellent wear resistance, as well as high hardenability, good machinability, low cold deformation plasticity, poor welding performance, overheating sensitivity, white spot sensitivity and temper brittleness. Water cooling is easy to produce cracks. Proper quenching and tempering treatment can obtain good comprehensive mechanical properties, which can be used after quenching and tempering, and can also be used after normalizing and tempering. |
| DIN 20MnV6 1.5217 GB 20MnV |
Its strength, toughness and plasticity are better than 1320, its hardenability is also good, and its machinability is acceptable. After carburizing, it can be directly quenched without the need for second quenching to improve the core structure, and its weldability is good. However, during heat treatment, it has temper brittleness at 300-360%. |
|
20CrMnTi 5115 SMnC420H 5120 20MnCr5 1.7147 1.8401
|
|||||||||
|
component
|
C
|
Si
|
Mn
|
P
|
S
|
Cr
|
Ni
|
Cu
|
Mo
|
|
minimum value
|
0.17
|
0.17
|
0.8
|
-
|
-
|
1
|
-
|
-
|
-
|
|
maximum value
|
0.23
|
0.37
|
1.1
|
0.035
|
0.035
|
1.3
|
0.3
|
0.3
|
0.15
|
|
30CrMnTi
|
|||||||||
|
component
|
C
|
Si
|
Mn
|
P
|
S
|
Cr
|
Ni
|
Cu
|
Mo
|
|
minimum value
|
0.24
|
0.17
|
0.8
|
-
|
-
|
1
|
-
|
-
|
-
|
|
maximum value
|
0.32
|
0.37
|
1.1
|
0.035
|
0.035
|
1.3
|
0.3
|
0.3
|
0.15
|
|
30CrMnTi
|
|||||||||
|
component
|
C
|
Si
|
Mn
|
P
|
S
|
Cr
|
Ni
|
Cu
|
Mo
|
|
minimum value
|
0.26
|
0.17
|
0.8
|
-
|
-
|
1
|
-
|
-
|
-
|
|
maximum value
|
0.32
|
0.37
|
1.1
|
0.025
|
0.02
|
1.3
|
0.3
|
0.2
|
0.15
|
|
Thickness (diameter, side length)
t mm |
Tensile strength
σb Mpa |
Yield point
σs Mpa |
elongation
δ5 % |
hardness
HBW |
Impact toughness value α kv (J/cm2)
|
Impact energy Akv (J)
|
|
t=15
|
≥1080(110)
|
≥835(85)
|
≥10
|
≤217HB
|
≥69(7)
|
≥55
|
| Tolerances | ||
| Pipe types | Pipe sizes(mm) | Tolerances |
Hot rolled |
OD<50 | ±0.50mm |
| OD≥50 | ±1% | |
| WT<4 | ±12.5% | |
| WT 4~20 | +15%, -12.5% | |
| WT>20 | ±12.5% | |
Cold drawn |
OD 6~10 | ±0.20mm |
| OD 10~30 | ±0.40mm | |
| OD 30~50 | ±0.45 | |
| OD>50 | ±1% | |
| WT≤1 | ±0.15mm | |
| WT 1~3 | +15%, -10% | |
| WT >3 | +12.5%, -10% | |
1. Bundle and pack.
Q1:who are we?
A:We are based in Shandong, China, start from 2022,sell to North America(60.00%),Western Europe(14.00%),South America(6.00%).
There are total about 11-50 people in our office.
Q2. how can we guarantee quality?
A:Always a pre-production sample before mass production;
Always final Inspection before shipment;
Q3.what can you buy from us?Which ports are accepted for delivery?
A:Copper,Aluminum,Mould steel, Seamless carbon steel,Precision steel pipe,The steel plate,Alloy steel,Titanium,Custom machine parts.It can be delivered from Qingdao, Tianjin, Shanghai, Guangzhou and other ports.
Q4.why should you buy from us not from other suppliers?
A:Shandong Meide Import and Export Co., Ltd. has 25 years of production experience. With advanced precision production equipment
and modern large warehouses, has a stockpile of 200,000 tons of goods, has a number of long-term stable cooperative customers.
Q5.what services can we provide?
A:Accepted Delivery Terms: FOB,CFR,CIF,EXW;
Accepted Payment Currency:USD,EUR,JPY,CAD,AUD,HKD,GBP,CNY,CHF;
Accepted Payment Type: T/T,L/C,D/P D/A,PayPal;
Language Spoken:English,Chinese
Q6.Can we get the some samples?Any charges?
A:Yes,you can get available samples in our stock.Free for real samples,but customers need to pay the freight cost.
Q7.How can we get your price ?
A:We need below information to quote for you:
1). Product Name
2). Standard
3). Material Grade (Chemical Composition)
4). Dimension
5). Quantity
6). The Drawing for Special Parts
ซัพพลายเออร์ที่มีใบอนุญาตการทำธุรกิจ
ซัพพลายเออร์ที่ผ่านการตรวจสอบแล้ว 
